I do not know if this source has been posted... but for those that may be interested... also is this a good deal for what is offered? AR-15LowerReceivers.com - 80% Lowers, 80% Lower Jigs & AR-15 Parts full setups here... 80% Lower and Jig Combo - AR-15LowerReceivers.com
When I can buy fully machined AR lowers for $50 on sale from Brownells, I see no need to buy these and finish them myself.
I haven't seen that site/brand before but there are a couple here on the monkey. One such is by @Tully Mars. Receiver Jigs | Survival Monkey Forums ***Neither of which is tagged***
Yes, but 80%s don't have 4473 generated when purchased. Granted you can buy 100%s face to face but If you go to a FFL, there will be a record of it.
@VisuTrac beat me to it, I bought 4 80% from that Cali company (now called AWC) that was being harassed by the BATF, $49.00, and bought a 80% AR10 from them also, and the jigs came from them, but I think I remember someone else makes them. The thing to look out for on 80%'r is for the rear well by where the stock thingie ma jig screws into, make sure it is milled because that is the correct floor for your first pass at milling out the lower. I also bought the Harbor Freight mini mill, and the add on belt drive because I knew I would strip out their cheap gears. Rancher
Not just Ar's Most common pistols can be built with 80% kits! 1911builders.com Matrix Precision, High Quality Parts Shooters Connection - Competition Shooting Supplies
...or purchase through private sale, especially from an executor of an estate couple of layers between you and the name on the FFL that was involved in the original purchase
I always shake my head at people that think they are hiding something by getting 80% receivers. Did you buy it online and use a credit card, your screwed. Unless you walked into their place, gave no info and paid in cash, your screwed. How did you buy the lower parts to finish it, your screwed. Also tired of hearing the old line about boating accidents. Here is the real deal...If it's time to hide it, it's time to use it!!!
In short, no. It's not a bad deal, but do a bit of searching and you can beat their price,esp. the single unit price. That is your decision and it may be fine and correct for you. I choose to "roll my own" nowadays.Machining the lower is not hard and I enjoy it. It also allows one to add some custom touches to their lower if they so choose. Just because a lower (or upper) is advertised as Mil Spec doesn't always mean it is on the tighter side of listed tolerances-often they are just the opposite.I can control that for the most part when I mill my own. It's great fun building one up from scratch. I am free to pick and choose what kind of components go into the build, which in the end will save me money. If a person wants a bone stock AR, this probably isn't the way to go as you can buy them for under 5 bills on sale. BUT, if you want a specialized weapon you can and will save money building it yourself. The latest one I built fires a five shot group from the bench at 100 yards that can be covered by a dime. The same weapon(except for the stock-I chose a fixed) available from a custom gunsmith sells for $3,500.00. Total cost for my build, including the cost of me doing the Cerakote was a grand. I will caution folks on trying to complete a semi auto pistol as their first project, esp. a 1911(A1). Although the Glock is easier than the 1911 both are harder than it looks without much room for error. Most all of the semi auto pistol kits require that you mill the rails that the slide runs on. Any mistake and at best you have a loose pistol, at worst the frame is scrap. Slow and easy, following the included instructions is the key. Personally unless a person has some machining experience I would suggest an easier build to start with (AR or a AK) YMMV
I love to build things, always have since I was a kid and that has carried over into adult and soon to be the geriatric life.... I weld wood, maintain the homestead, RV, fish, hunt, shoot guns, build guns and reload for hobbies and all that seems to keep me busy for a retired old fart. Do I care in this day who knows what? NO, we have no secretes anymore because of this retched technology and how it's been exploited by TPTB. I would not be heartbroken if it all went away.... This right here is the most foolproof way to get EXCELLENT results from milling your own lowers. 80% Lower Jigs - AR-15 | AR-10 | AR-308 | 80% Lower Receivers
Just finished an 80% with a 5D jig. Messy, as shavings go everywhere, but a well built jig. One of the best guide systems I've seen with built in depth gauges. Recommended.
Unless, of course, you simply want to know how to do it in case of need. Or maybe it's just a hobby? To add that sure, it's expensive, but that is NOT the point of DIY. As to how simple it might be without the jigs, that's in the eye of the beholder. Sewing buttons is easy, too, after the first one. So is darning socks. Neither of those require a sewing machine, much less a router and drill.